Stamm Manufacturing

  • Increase font size
  • Default font size
  • Decrease font size
Home Products Aerial Buckets Signalier ATR 41 N Specifications

Signalier ATR 41 N Specifications

GENERAL SPECIFICATIONS

ATR –41–N  SIGNALIER

 

This section describes each of the ATR-41-N major (standard) components.

 

PLATFORM – 42" X 66" Aluminum Platform with 24” door. Constructed of  1 ½” aluminum pipe schedule 40 bent at 6” radius for corner strength.  Floor is aluminum diamond plate 3/16” with 4” kickplate. Mounting Plate to Rotation Motor using 12 Bolts Grade 8 with Torque Strips. Mounting Plate to be made of Core Ten 1/2" thick. Wide Bracket Mounting on Platform offset mounting on Platform for Stability in operations, 2 braces on side of Boom Tip Pin to support side movement of Platform. Continuous upper rails on Platform, 30" door for access to Platform. Rubber Bumper mounted to Platform.

 

PERSONNEL RESTRAINT SYSTEM – A safety belt or harness and a lanyard are provided.  The anchor for the lanyard is attached to the upper platform support.

 

INDIVIDUAL LOWER CONTROLS – Individual full-pressured controls at the turret actuate all boom functions.  An emergency stop and a tool selector control are located at the upper controls.  The lower control station is equipped with a selector valve to override the upper controls. Lower controls are internally mounted in turret for protection.

 

SINGLE STICK UPPER CONTROL – The full-pressure single-stick upper control includes a safety trigger to prevent inadvertent operation.  The lift movements correspond with control handle movements.

 

HYDRAULIC PLATFORM ROTATOR – A hydraulic platform rotator model HELAC L10-5.5-E-RF180S10H, operated by a control lever, rotates the platform 180 degrees from one side of the outer/inner boom assembly, across the end-hung position, to the other side of the outer/inner boom assembly.

 

HYDRAULIC PLATFORM LEVELING – All leveling arms must be internal of boom/NOT OUTSIDE. A master and slave cylinder controls platform leveling.  The leveling system can be operated from the upper controls to adjust platform leveling, tilt the platform .

 

OUTER/INNER BOOM ASSEMBLYCompensation links must be located in side the boom for protection. The outer/inner boom assembly includes an outer boom, telescopic inner boom, extension system, and hose assemblies.  The outer boom consists of an 8 in. x 10 in. (203 mm x 254 mm) rectangular steel section. The 6-1/2 in. x 8-1/2 in. (165 mm x 216 mm) rectangular aluminum inner boom is housed within the outer boom.  The inner boom can be easily removed and disassembled for service and inspection.  The extension system consists of a hydraulic cylinder, two integral holding valves, and dual #50 roller chains housed entirely within the boom assembly.  The hoses routed through the outer/inner boom assembly are fully contained within the boom assembly. Main boom strapped for extra strength to prevent bell mouth during long term use with 1/2" x 2" welded to boom.

 

The outer/inner boom assembly articulates from 25 degrees below horizontal to 85 degrees above horizontal.  Actuated by a double acting cylinder that has two, integral holding valves, the outer/inner boom assembly is offset to one side to provide easy access to the platform.  A boom support cradle and a boom tie down strap are included.

 

LOWER BOOM Compensation links must be located in side the boom for protection. The rectangular 8 in. x 10 in. (203 mm x 254 mm) high strength steel lower boom is designed for maximum strength and rigidity.   The double acting cylinder, with an integral holding valve, allows the lower boom to articulate from horizontal to 80 degrees above horizontal.  The lower boom encloses a parallelogram linkage to maintain the knuckle at a constant angle to the turret.

 

CYLINDERS – Both the upper and lower cylinders are a threaded head-cap design.  The upper cylinder is equipped with two integral holding valves that prevent down creep and to lock the booms in position in the event of hose failure.  The lower cylinder is equipped with one integral holding valve.

 

TURRET – The turret wings are designed for strength and rigidity.  The bearing cover is continuously welded to seal out moisture and prevent foreign materials from obstructing the turret rotation.  The turret plate is machined to provide a flat surface to support the rotation bearing.

 

CONTINUOUS ROTATION – Unrestricted rotation is accomplished by a hydraulically driven worm and spur gear with a shear ball rotation bearing.  The critical bolts holding the lift to the rotation bearing and the rotation bearing to the pedestal are hex head capscrews.  These critical bolts are torque seal marked to provide a quick means of detecting any turning of the bolt upon inspection.  The eccentric ring backlash adjustment (gearbox pinion adjustment) is described in the “Adjustment” Section of the Service Manual.  Also refer to drawing in the “Adjustment” section to set gear backlash.

 

LUBRICATION – Non-lube bearings are used at most points of motion.  The rotation bearing and extension chain require periodic lubrication.

 

PEDESTAL – The pedestal is tubular with reinforced mounting plate.  The top plate of the pedestal is 1-1/4 in. (32 mm) thick and machined flat to support the rotation bearing.

 

HYDRAULIC OIL RESERVOIR – A 17 gallon (64.41) hydraulic oil reservoir is built integral to the pedestal.  The reservoir includes anti-splash baffles and two sight gauges for quick hydraulic fluid level checks.

 

HYDRAULIC SYSTEM – The open-center hydraulic operates at 2700 psi (176 kg/cm2) at 6 gpm (22.7 lpm).  A 10-micron return line filter, mounted above the hydraulic oil level and inside the pedestal, can be easily changed without draining the reservoir.  The 100 mesh (149 micron) suction strainer in the reservoir can be removed for cleaning.  A gate valve, located below the reservoir, prevents oil loss when the pump is serviced.  A magnetic drain plug attracts metal particles from the oil.

 

PAINT – The complete unit is primed and painted prior to assembly. Safety yellow or Bell white enamel paint is standard.

 

HOSES AND FITTINGS – The hoses routed through the booms are high pressure and nonconductive with swaged hose end fittings.  Retainers separate the hoses inside the booms to prevent chafing and nylon sleeves are installed over hoses at points of movement.  Reusable fittings can be installed if a hose is damaged.

 

MASTER CONTROL – The master control energizes the upper and lower control circuits, including engine start/stop and optional two-speed throttle control.

 

ENGINE START/STOP – The start/stop circuit has been designed so the lift cannot be operated unless the truck ignition switch is in the “RUN” position and the master control is activated.  This feature makes it difficult for unauthorized individuals to operate the lift when the truck is locked.  An air cylinder at the upper controls and a toggle switch at the pedestal energize this system.

 

HYDRAULIC TOOL CIRCUIT AT THE PLATFORM – This system uses open center hydraulic tools.  The tool circuit provides 6 gpm at 2700 psi .

 

MANUALS – Two operator’s manuals and two service manuals are included with each aerial lift.

INDEPENDENT OUTRIGGERS – A-frame outriggers are shear-plate mounted to the frame and are equipped with pilot operated check valves, internal thermal relief valves, and separate controls.

At maximum extension, the outriggers furnish 96-in. (3.05 m) of spread and 9 in. (229 mm) of penetration.  They have 17 in. (432 mm) of ground clearance based on 36-in. (0.91 m) or 31 in. (0.79 m) frame height.

 

PIVOTING OUTRIGGER FEET – Pivoting outrigger feet swivel 12 degree angle about a horizontal centerline.

 

OUTRIGGER/BOOM INTERLOCK SYSTEM (optional) – The outrigger/boom interlock system prevents lift operation until the outriggers contact the ground and outrigger retraction before the aerial lift is properly stored.

 

EMERGENCY POWER (standard) – The emergency hydraulic pump is driven by a DC motor, which is powered by the truck-engine battery.  The system is connected in parallel with the main pump and is designed for non-continuous operation.  An air cylinder at the upper controls and a toggle switch at the pedestal are used to energize the system.

 

SET OF TOOL POWER PORTS (standard) – A set of power ports are installed at the platform to accommodate an open center tool.

 

TOOL POWER AT THE GROUND CONTROLS (optional) – The hydraulic tools must be open-center and operate satisfactorily at 2500 psi (176 kg/cm2) and 6 gpm (22.7 lpm).

 

LEVELING CONTROL AT THE TURRET – A valve section is added to the lower control station for platform leveling.  In addition to the control at the platform, the leveling control at the turret can be activated to tilt the platform for cleanout or to ease the removal of an injured operator.

 

BODY - Standard recommended 9’ service body with a 4’ rear floor extension. Aluminum tread plate on top of compartments and standard shelving. Access step at  rear.

ATR-41-N SIGNALIER

DIMENSIONAL SPECIFICATIONS

GENERAL SPECIFICATIONS - Based on 36 in (0.91 m) Frame Height

Horizontal Reach 32 ft.
Standard Platform Capacity 600 lbs

Standard Pedestal

Height to Bottom of Platform 36 ft
Working Height 41 ft
Stowed Travel Height under  9 ft 10 in (3.00m)
Weight of Lift 3,500 lbs. (1590 kg)

Hydraulic System

Operating Pressure 2700 psi
Flow Rate 6 gpm
Filtration 10 micron Return
  100 mesh Suction
System Type Open Center
Power Source PTO Pump or Clutch Pump

 

ATR-41-N SIGNALIER

VEHICLE SPECIFICATIONS

Recommended Cab to Rear Axle Dimension 60 in.(1.52 m)
Frame Section Modulus 10.1 in3 (166 cm)
Frame Resisting Bending Moment 727,200 in-lbs.(82165N/m)
 
With Outriggers
Axle Ratings Recommended Minimum
GVWR 19,000 lbs. (9753 kg)
GAWR (Front) 7,000 lbs. (3630 kg)
GAWR (Rear) 13,500 lbs. (6805 kg)

Approximate Weight for Stability 11,500 lbs

 

Notes: Actual GVWR and GAWRs should be based on the weight and weight distribution of the chassis, body, lift, ballast (if required), accessories, and the desired payload.

Curb weight of the unit will vary based on rated platform capacity, mounting configuration, frame stiffness, and stability test requirements.

**Platform lift must have been in use for at least 2 years -- No prototypes accepted.

*******

TRUCK SPECIFICATIONS

1. General

1.1 All unit(s) bid must meet or exceed the mininum requirements or they will be deemed incomplete and will not be considered for bid award.

1.2 All specifications written are to minimums, unless otherwise noted.

2. Manufacturer/Model

2.1 Unit(s) bide must be new standard production model as offered for commercial trade.

3. Item 1 - Cab and Chassis-

3.1 Engine:

a. Eight (8) cylinder turbo-charged diesel

b. 350 horsepower

c. 650 ft. lbs. of torque

d. 110 VAC engine block heater with exterior plug mounted in or near front bumper.

3.2 Transmission/Drivetrain:

a. Five (5) speed electronic automatic

b. Heavy duty transmission oil to water cooler

c. PTO capable

3.3 Steering:

a. Hydraulic power steering

b. Standard steering wheel

3.4 Brakes

a. Hydraulic anti-lock brakes

b. Trailer tow package with electric brake controller. Controller shall be factory integrated.

3.5 Front Axle & Suspension

a. 7,000# capacity rating front axle (4x2)

b. 7,000# leaf spring suspension

c. Heavy-duty double acting shock absorbers

3.6 Rear Axle & Suspension

a. Limited slip rear axle with a minimum 13,500# capacity rating.

b. 13,500# rated leaf spring type suspension with auxiliary

c. Dual rear wheels

d. 4.88 Axle Ration

3.7 Gross Vehicle Weight Rating

a. 19,000#

3.8 Wheels/Tires

a. 8-hole steel disc wheels (6)

b. Front - LT225/70Rx19.5 LR Tires to meet the rate weight of the vehicle fully loaded. Standard tread tubeless steel belted radials.

c. Rear - LT225/70Rx19.5 LR Tires to meet the rate weight rating of the vehicle fully loaded. Max Traction tread tubeless steel belted radials. (4)

3.9 Electrical System

a. 12 volt, 120 amp alternator

b. Two (2) 12volt sealed maintenance free batteries

c. Engine oil pressure gauge

d. Coolant temperature gauge

e. Fuel level gauge

f. M.P.H. speedometer

g. Mileage odometer

h. Variable speed windshield wipers with electric washer pump and reservoir

i. Lighting to comply with all state and federal regulations

j. Trailer tow receptacle wired to color code

k. Four factory installed up fitter accessory switches shall be provided

l. 80 dba backup alarm

3.10 Cab

a. Conventional type cab

b. Two full width cab doors

c. Adjustable front split bench seat with vinyl cover - individual adjustment for driver and passengers

d. Seat belts for three (3) passengers

e. Full vinyl/rubber floor covering

f. Factory installed air conditioner, heater and defroster

g. Dual trailer tow outside rear view mirrors

h. Tinted glass

i. Light Bar Type Ecco EC15-00036

3.11 Frame

a. Steel channel frame rails painted black enamel

b. Cab to Axle (CA) of 60"

c. Painted steel front bumper

d. Minimum two (2) front tow eyes fully braced to the chassis frame.

e. Trailer Hitch Receiver/Pindle hook combo type, removable with two inch ball. Two safety chain D ring hooks.

3.12 Fuel Tank

a. Minimum Forty (40) gallon fuel tank

b. Rear tank skid plate

3.13 Paint

a. Standard trim - painted white

b. Grey interior color

BODY SPECIFICATIONS

Page One

Body Spec 1

Page Two

Body Spec 2

Page Three

Body Spec 3